New Design for Drone

I have been playing my C gaita recently and I decided to make a small drone to go with it. I did not want to make the large C drone that normal go with a C gaita, but something I can carry around and make drone while I practice. I drilled though a piece of Bubinga wood and made 2 half from the one piece, 50cm each length. internal bore was 6mm. then I began designing the top sliding part. the internal diameter was 12mm. and I played around with the design.

The bottom standing part has an outside diameter of 12mm. the overall outside diameter of both pieces was 15mm.
The design for the bottom standing part was an idea I have been had for sometime and I wanted to try it out. if it did not work it could always be used for a chair leg!!

When I make the reed I will cover it in a removable stock and this will be inserted into a drone stock in the bag. It plays in C and I will make different sections for the top/movable part so I can play in D and Bb. I was gonna drill holes further up the drone but I decided to make new sections. This will add to the tembre of the sound.

I also intend to make a middle section to this C drone until I have a bass C playing alongside this tenor C. with 2 drones going it will be nicer for the gaita chanter which can be quite shrill. I have been thinning down the reed and now it plays a lot quieter than normal, this is for use indoors (pub setting).

Advertisements

Bagpipe Society Blowout, 2015

It was my first time at the ‘blowout’ (Polesworth, Tamworth, England) in a beautiful surrounding of the Abbey. Each piping culture has its traditions and this was a new tradition for me. Here there was a different style and feeling about the music, pipes, people and events, perhaps a more European style or perhaps an ‘English” style. I say English as it is a reinvention of a tradition that died out. And the reintroduction of the tradition has established a very firm and loyal group of people to their type of music.

I was expecting a heavy influence of French music, but I was surprised to see a good mix of styles in the form of workshops and concerts: Northumbrian/Borders; Occitan from the French Pyrenees; Hungarian; Irish; Welsh… these music’s were played on a type of bagpipe that I have a problem in naming.

They call it a “Border pipe” but I cannot see where their border is exactly? The majority played a type of pipe similar to the French/Belgium bagpipe: mouth blown or bellows blown, conical bored chanter, 2 drones, over-blown into a 2nd octave. Not so loud, plastic reeds, no African Blackwood in sight (made a nice change too) therefore the sound was mellow, perhaps they could call it a “French-Anglo Pipe” as the makers are English and the pipe is modeled on the French/Belgium style.

The makers present (selling their pipes) were in the main hall alongside a Society stall, a flute maker, an Occitan maker. Zampogna maker. There was a 2nd hand section of music books, CDs, cassettes…

One of the workshops I attended was a ‘beginner’s workshop’ to sort out teething problems players were having. This was very informative as it gave me a chance to see how the workshop was structured (with relation to my own workshop); I was also looking for some advice about my Spanish gaita as it was sharp in the bottom notes.  It came apparent that the information was only for a select type of pipes from a select few pipe makers. A general knowledge was not there of conical bored pipes.  The Society was open to all pipes but in reality (at this blowout in particular) only certain types of pipes were represented. Sometimes it felt like if you did not have a bagpipe from a certain type of maker then you were excluded from activities and advice, there was no advice about the Gaita. Also it presumed that because I had “asked the question” that I did not know anything about pipes or conical bored pipes, and I was told to go and “ask (someone) and you will find that the pipes are fine” (meaning “it is you who is wrong” well it seems I know as much as the person who is giving the advice, as he did not know either, a little condescending I thought).

The only sessions available were in D or G, G being the more popular of the 2. G pipes are common in French music, a large bass G. Which is fine, they sounded beautiful. But there are other pipes and I would have liked to have seen a session where any type of pipe could have been played… a few people had brought their sackpipa (key on A minor), , Spanish gaita (C),  , I had with me bagpipes in A minor, C, A major, D, F, and C minor… but no G. I did attend the Irish workshop which was in D, but others I could not. This did not lesson my interest. Other pipes present were a Welsh Pibgorn (D), Leistershire Small pipe (D), Italian Zampogna and there was a Dudy from the Czech/Slovak regions.

The D session on the Saturday was titled “English Session” this apparently is a new occurrence as only English melodies are played (I did not know this at the time and I played a Catalan melody which was met with a silence). After I realized my “mistake” I tried to play along with the English melodies, which there was a lot of. This was the biggest surprise of the weekend, a firm selection of English tunes were being played by all. The Northumbrian tunes came at the end of the night when they had played out all the English tunes. This is great as it establishes a firm melody base of for an English tradition, and leaves the Northumbrian tradition a little apart (which I feel is more accurate as it is more akin to the Scottish/English Border tradition).

Another surprise for me was the Occitan music and bagpipes. 2 makers from the French side of the Pyrenees were offering their instruments for sale, CDs, workshops and concerts. It was a music I only knew a little about (and only recently). They seemed to have a cross-over from the Catalan and Aragon side of the Pyrenees with the Sac de Gemecs (made from a fruit wood, a type of apple) and the Gaita de Boto (complete with snakeskin and girls dress). But also they had their own type of pipes a very large bagpipe in F with a large drone with a knitted “flecco” (decoration). A shepherd’s bagpipe without a drone, deep sound, sad sound, lovely (I had heard this on the Spanish side of the Pyrenees). And the Boha bagpipe with the drone apart of the chanter which can play 2 notes… (Therefore is it really a drone?). Also there was a variant of this having 2 melody pipes and 1 ‘drone’ built into the chanter, single reeds, polyphonic sound.

In the sessions I heard the Welsh Pibgorn, a dingle reeded instrument, 1 octave mouth blown with a distinctive sound, a beautiful decorated horn cut away at the bottom of the chanter, with cylindrical bored chanter.  Their melodies were not dissimilar to a Breton tune, in a minor mode.

The Hungarian duo (pipes and hurdy gurdy) were fantastic players, (I had seen them at the Piping Live Festival in Glasgow a few years previous) tight in their music and ‘tuning’ (an important lesson for us all). Played beautifully with traditional and composed pieces, improvisations and structured parts. The pipes were not so dissimilar to the Occitan Boha. With the Hungarian ’suggesting’ that the Boha was taken from their pipes. They look similar… but who’s came first is a question too far…

My final observation of the weekend was that there is a danger of the “small pipes” becoming obsolete in time due to their quiet nature. Those who had them were drowned out by the conical chanters. This is a reflection of what is happening in sessions too all over the country. If you are “not heard”, why play them? The highland pipe makers are increasing the volume of the “session small pipes” but not so with pipe makers (although there are exceptions). Perhaps the small-pipes need to become more assertive, and insist the venues, meetings, and festivals are predominantly ‘small-pipe sessions’ the same way the ‘English Session’ has become?

Drone Design with Computers

I spent too much time over a drone yesterday. The boring and rough turning was done the day before, so all was left to do was shape it, but this is where the time went, designing and turning all has to be done in my head then acted upon; and since it has been months since I had made a drone I was again remembering how to do it. I had altered the design since last time too by using new measurements and new forms; using my chisels instead of the tool post and cutters. It was a success, it looked ok, until the last piece was to be turned and here (again) tiredness took over and I glued the finishing piece and left it for the night. I should have left the gluing until today, as it was not long enough. Not to worry the beauty about wood is that you can redo it.

Later I decided to revisit the design of the drone, not in my head, but on the computer by using a “vsd” format. This allows quite detailed drawings to be experimented with, and a working blueprint to be achieved ‘on paper’. So I am hoping today I will have gained some time and drones will not take so much time.

I started working on my new idea for the bellows, I submerged the wood into a barrel of water to make it more supple, then I laid heavy weights on it to iron out any lumps and bumps, and then let it to dry.

Drone Configuration and Melody Types

An interesting talk with a young piper yesterday in Carlisle prompted me to write a little about drone tuning. Our conversation centered on the types of drones one should use and for which melodies. He was interested in using the drone configuration of A, d’, a’’ (Bass A, tenor D, alto A) with his ‘A’ Scottish small pipes. This drone configuration is not unusual in the European style but it is with Scottish small pipes. When I first heard about it I was skeptical, there would be a clash of sounds, but it was not as bad as what I thought as I listened to him play.

The problem is the amount of melodies he could play, not many would fit the harmonic arrangement. The Highland tunes would be more willing to blend in with the drones especially the one which were routed in the D note, but the Northumbrian and Border melodies that used the C# (3rd note of the A scale) a lot clashed with the D drone. He thought it sounded ok, but I begged to differ.

When I started to play the Northumbrian small pipes in G I looked for melodies that played with the A drones (a’, a’’) there was not many melodies either, the root note of the melody being the A note on the chanter. With the drone playing the root note it harmonized with the rest of the scale. Not a problem.

My young friend was interested in a small pipe that “fitted all situations”, I was too, many years ago and in some respects the addition of owning chanters reflect this still. But perhaps this has been tried before, in the past, and the best that was achieved by the tradition was a drone configuration of A, a’, a’; giving a strong root note for different types of modes/scales to be explored. For me it was interesting to see a “work in progress” but I wonder if it will be followed up in a few years time… I hope so.

Drones, Bellows and Reeds

I have not turned any drones for a couple of months so yesterday morning I had to spend most of my time trying to remember how to do it, or in what order I should do it. Also, within those months I have changed my making process and now I do things differently. What is the point (besides documentation) in writing anything down, to remember the process, when it is changing all the time?

With the new drill I bought the boring and drilling went very well, I did 2 sections of wood which will become a tenor drone.

Later that day I got given some wood which will become bellow cheeks. A change of design has been growing in my mind for several weeks now, to make the design of the bellows more airtight. My present system is an adaptation of the traditional method, but I have this idea and it will not go away! What I need to do is try it out, and this wood will be ideal for that. The process is not quicker but I believe it will be a cleaner and more secure/airtight that the traditional method.

I bought screws for the bellows cheeks, not the ones I was looking for, but they will do for the traditional bellows. This is the problem of making pipes in 2 countries (Spain and the UK), there is not the same product in both countries, not the same measurements and not the same price, and availability is not the same either. These screws will do for now until I can source better ones.

Later on that afternoon, I met a piper and we went to the park in Carlisle, the meeting was an interesting one but for the point of this blog I noticed that the reed I had made was not so bad. It was louder than what I had thought and the tone was sweeter. There were some problems with it (too sharp in the chanter) but from the point of view of making I was pleased.

Removable Chanter Stocks

Yesterday I made 5 removable chanter stocks; these stocks are made for each chanter so they protect the reed if removed from the bag.

In hindsight I could have made only the bag/chanter stock, but this is not only about the workshops, it is also about learning and creating a finish product I am pleased with. The bag/chanter stock would have been quicker but the chanter would have to fit each chanter stock exactly and I would not be able to interchange the chanters in different bags if there were any deviation in size. This might have been limiting if a student wants to try Northumbrian fingering and then they want to try Scottish small pipe fingering… they would have to change bags, bellows etc. which is all time consuming. With the removable option I can simple take one chanter out of the bag and add it to another without damaging the reed (most damage done to the reed is when it is removed from the bag).

As I was completing the 4th stock it suddenly jumped out of the chuck in the lathe and crushed itself against the tool post. Tiredness and lack of concentration can be dangerous. It is the first ruined piece of work so far… well there has been many failed experiments but this was my first broken experiment. It was a valuable lesson “take a break and rest”. Bad things happen very fast indeed!

Stocks and Newcastleton Folk Festival… it’s on !

At the end of the day I had 5 stocks completed, the drilling on the wood lathe went ok but the shaping and finalizing the stocks on the metal work lathe took the time. Also I had problems with the motor, it kept on speeding up then slowing down, I had to reduce the rpms to keep it stable, and so I was cutting slower. Anyways, it is progress and still on schedule.

Today I finalized the dates of the workshop at Newcastleton Folk Festival, so it is official, I will be giving a beginners workshop on the “Bellows blown Small-pipes”. The aim of the workshop is to introduce the student to the techniques of bellows blown piping, with ideas on bellows technique, bag pressure, holding a note, keeping the drones steady, and if there is time playing a scale… basically everything except learning melodies….that is for another workshop. With these techniques one can adapt to any of the bellows blown bagpipes (Irish, Border, Northumbrian, Scottish Small pipes, Pastoral, Dudy, Cornemuse, Mussette, etc.), as the basics are the same. If you are buying a set of bellows blown pipes with these techniques you can see if the pipes are in tune, working, playable… without the basic techniques this is impossible.

Stocks, Stocks and more Stocks

I realize I am starting late in documenting my attempts at making “small pipes” it is better to start now while I am still in the process of making, than to leave it and forget what I have done. The idea is to make at least 6 sets of small pipes to use in workshops at folk festivals. I think between 6 and 10 sets are a realistic number, 6 being the minimum to start with then increase it if I have the time. I get the chance to give my first workshop at the Newcastleton Folk Festival in July 2015.

There has been a lot of experimentation over the past year, but a few months ago when I was told I could do the workshop I had to get together the experiments (that worked) and start assembling them. I should also add that most of these experiments were done in Madrid, Spain. There I had tools and wood easily to hand, on returning to the UK I had to source all the materials again and things were harder to find here, and some things were not possible to get, so I had to begin again and experiment. Time was running out but today I thought to allocate time to each stage, for example last week and this week I dedicate my time to making stocks and by the end of the week I move onto the next stage eg. Drones. By this method I should complete at least some if not all of the small pipes in time, leaving enough time for tuning! So I began today by making stocks for each bag that did not have them, and I will work my way through the missing stocks systematically until all have them.

I have made 6 bags so far (I have made more, if I need them), I have inserted some of the chanter stocks, blow pipe stocks and drone stocks, but as I go along I notice I have to do little changes to them. For example, originally I had made the internal diameter of the blowpipe sock 16mm but I later noticed that it would have been better to make it 18mm so I have to enlarge it. Not big jobs but multiply it by 6 it can take a few hours. This is what I mean by “experiments”.

Today I made 4 bag stocks: 3 chanter stocks and 1 drone stock. The drone stock took most of the day due to slowly boring the stock then shaping the outside. I had an old bag which was precut, so I had to match the diameter of the hole in the bag, I did not have a large diameter piece of wood and when I found one it took some time to prepare it for drilling.

The 3 chanter stocks were not a problem; these can be tired into the bags when I get some better twine. This will complete what is required for the 6 sets.

This morning I placed the 6 bags on the floor and placed beside them the things I have made so far. I had made about 3 sets but something was wrong with all of them, so I will have to take the stocks out of the bags and redo them at a later date. It was a useful exercise as I could write down what is still needed to do, and what things I need to prioritize. The 3 bellows I have already are nearly complete I need to make one more here (as I have the cheeks cut already) and do the rest in Spain.

Small-Pipe Workshop Update at Newcastleton Folk Festival

The progress is slow but sure, I have 6 bellows at the moment, some have been donated (one by David, the organizer of the Newcastleton Folk Club, many thanks to him) and others I have made; so there will be at least 6 sets of pipes on the day for beginners to use.

I would also like people who already have a set of small-pipes but do not play them/cant play them, but wish to do so to come along also, it is all about getting you started, sorting out the beginners problems that we have all gone through. So if you know of someone who has given up trying to play or has a set in the box at home which have been put away in frustration ! encourage them to come to the workshop.

Players who have Northumbrian sets we will be using the big drone at first (the D/C drone) this will be compatible with the sets I am making in D. Scottish Small-pipers are generally in A or D so a harmony can be achieved… all this can be sorted out, the workshop is about bellows technique, bag pressure, keeping the instrument stable, getting all parts in harmony, and obtaining a scale in tune with the drones, and if there is time left a melody

if you wish to contact me regarding the workshop or anything to do with piping can do so at tilbsuk@yahoo.com

!

Small-Pipe Workshop

I will be offering this year at Newcastleton Folk Festival a beginner’s workshop in “Learning the Small-Pipes”. The workshop will be a basic introduction into small pipe techniques. 
Too often the beginner will not take enough time to learn the basic techniques of the bag, bellows, drones and chanter, and rush towards learning melodies and then finding out later that they have to restart learning, also most damage caused to a new instruments happens in the first few days of receiving their pipes. 
The workshop will go through the basics of bag pressure, bellows technique, tuning drone and fingering styles, and reeds. The workshop is designed for people who intend to start playing the small pipes not for people who already play them.
Buying a set of small pipes can be an expensive hobby, and often there can be a long wait to get a set of pipes. It is a commitment before you can start to play, and often it can be frustrating when you get your set, and often they are put aside as there are many things to do at once before getting a good sound from them.
If you are thinking of buying a set of small pipes, or waiting for your set to be made, or just wishing to try the instrument out… this workshop is for you.
It is also for people who have already their set of small pipes, perhaps the instrument has been put aside as it was found too complicated, bring them along and the workshop can help you to get started.
I can offer a limited number of small pipes for those who attend the workshop. These will be for those interested in Northumbrian Small pipes and Scottish Small pipe players, with open and closed fingering.
There maybe is also a chance to try mouth blown examples too…
Reservations is the best way of ensuring a place on the workshop, or just turn up on the day if there are sets available, those with their own sets bring them along too.
I am trying to ensure there will be 10 sets of small pipes available on the day. I will be posting updates to confirm the number of pipes available.  

Gaitas at Christmas

The cold is affecting the gaita, it takes about 15 minutes to warm the reed up and to settle the drone reed, until then it is unstable. 

When it settles down I start with a mix of Asturian and Catalan melodies, a few from Zamora and I am now slowly introducing melodies from Galician and Northumbria. 
The melodies are well received by the general public, whether it is the new sound I do not know but they seem to like the melodies, which is encouraging. 
I am playing a Galician chanter in D, this is bought in Madrid and has a high pitched sound. The reed is constantly changing due to the damp and cold, so I have to alter it until it becomes stable, but when it is stable it has a nice contrast with the bass drone. This drone is from a Highland Bagpipe, the big bass drone, it sounds a D (440c)… , in fact I bought this Highland bagpipe in India in 1995 while I was there researching music. There is a metal tongued drone reed but it does not seem stable in the beginning, probably due to the large bore size of the Highland drone…  I need to make the bore smaller. 

I added “fleco” to the drone… a typical decoration that the Spanish bagpipes have. The drone sits across my arm (not over my shoulder) like the Border pipes; I did this because the drone was being scraped against the wall so it was not practical for playing.

A New Musical Project

I have been playing more these days, learning new tunes… sometimes I do not practice for weeks, but these days I am learning a new repertoire for concertina, Scottish small pipes, Northumbrian Small pipes and Spanish gaita. This increase in playing could be because of a new project I have started with a Spanish fiddler called Alba. She lives in Madrid and we have decided to play together and start performing in public. We have known each other now for a few years and have a repertoire already, so it is a case of finalizing it and practicing. 
We are playing familiar and unfamiliar tunes from Northern Spain and the Scottish and English Borders… some from Ireland too. But we hope we are “highlighting” our musical “accents” not copying a style but interpreting the music in our own way…  using our musical culture and nationality/s to change the melody… to add and take away something.

I am playing Spanish melodies in a Border/Northumbria style… (we are limiting ourselves to areas such as Galicia, Zamora, Asturias, Basque, Catalonia, Mallorca…) and Alba is playing Northumbrian/Scottish Border melodies in a Spanish style… so a jig is not really a jig and a jota is not really a jota… the Irish melodies are not played in an “Irish style”, but something “foreign” to both of us!
It is an interesting project, finding a name, exploring the music and trying to practicing while we are in our own countries and meeting when we can… but we hope by spring 2015 we will be ready and performing live.

We have a set list worked out and it is an interesting mix of music, this list will probably change as time progresses so it is interesting to record it for now:
Zontzico / Morfa Rhuddlan (Basque/Welsh)
Old Drops of Brandy (Borders)
O’Carolyn Set (Irish)
Alloa House / Romances (Scottish/Zamora)
Mr. Prestons Hornpipe (Borders)
Sir John Fenwicks (Northumbrian)
Newmarket Races (Northumbrian)
Jackey Layton (Northumbrian)
Ann Thou Were My Ain Thing (Borders)
Autumn Child / Rights of Man / Proudlock’s Hornpipe (Irish)

Morigana in Spain / Welcome to Vigo / The Spanish Cloak (Northumbrian/Scottish/Irish)
Redondela / Saddle the Pony (Galician/Irish)
Noble Squire Dacre / Go to Bewick Johnny (Northumbrian)
Basque melody / Roxburgh Castle / Hesleyside Reel (Basque/Northumbrian)
Bollero de St. Maria / Zamora Melody (Mallorca/Zamora)
Galician Melody / Frisky (Galicia/Northumbria)
Highland Laddie (Borders)
Loch Ryan / Bonny Millar (Scottish Highland/Borders)
This probably needs more Spanish melodies… or to take away a few UK melodies … early days yet !!
The instruments will vary also, Alba plays violin and a Baroque violin, this depends if I am playing concertina (440c) or Northumbrian Small pipes (415c)…

Galician and Border Fingering – Cross Fertalization

Often when we learn an instrument we learn ‘patterns’ for our fingers to use on the instrument, this is an aid to learning an instrument and memorizing tunes. We become accustomed to these patterns and form them into a ‘tradition’ which develops into a certain regional or national style. But, what is important is the ‘sound’ to play the melodies as they should sound and achieving the sound should be more important over technique.

Finger Chart for the Highland, Scottish Small-pipes, & Border Bagpipes

I have deviated from the normal ‘tradition’ on the Border pipes, I am adopting a different tradition of fingering the chanter. This mainly concerns the top A note which is fingered traditionally with the bottom hand oxxx and with the top hand xoo o (oxxx xoo o) this is a Highland bagpipe style, which in my opinion is a different style of music to the Lowland piping tradition. 

I have been playing Border/Northumbrian melodies using the traditional fingering for a number of years it suits it well, but there are characteristics of the Lowland music which make this fingering of the top A note cumbersome and problematic. There are many ‘jumps’ in Lowland music from a high A down to a lower register, and this can cause a lot of hand ‘waving’ on the chanter (The Highland bagpipe style uses a closed finger technique that lifts multiple fingers off and on the chanter) as the top hand opens so closes the lower hand. It can be messy, especially if the melody demands a quick run or semi-quaver ‘jumps’.

I have been learning the Galician bagpipe for 3 years and they use a different fingering for the high A note, (oxxx xxx o) all fingers closed and only the thumb hole open. It is this technique I have been adopting for the high A on the Border pipes.

At first it was to put the chanter in tune with itself as it was a bit sharp on the top A, so instead of taping or gluing the hole I changed finger technique. Another reason why I used this Galician fingering was I fitted a Galician Bb reed to my Border chanter. I scraped the reed so it was softer to play and could sound a top A in the traditional Lowland fingering, but I found it gave a good high A in the Galician style too.

There are a lot of quaver notes in the Lowland repertoire that ‘jump’ in quick succession e.g. AaAbAcAd. This could mean playing oxxx xoo o for the high A then playing ooxx xxx x for the low ‘b’. I have found it easier to play these notes by using the Galican style oxxx xxx o for the high A then ooxx xxx x for the low ‘b’. this makes life a lot easier.

If you know the fingering style of the Northumbrian Small Pipes then you will know that this style of playing uses a totally closed finger technique, one finger is lifted off then replaces before the other is lifted. So jumping from a high to a low note is not a problem. This Galician high A position is similar in style to the Northumbrian as only the thumb is removed while the rest of the fingers stay on the chanter.

Of course there is no evidence that this finger style was used in the tradition of Border piping….but there is no evidence to prove it was not used either. The music certainly allows for an easy way of playing these ‘jumps’. and the Galician high A is one solution. In practise, I tend to mix these 2 finger styles, depending on the melody, some runs require it others do not.

In the Border/Northumbrian tradition at least there has always been a healthy innovation, without it the Northumbrian Small Pipes would never have evolved. It is easy to imagine these innovations coming about by influences from outside of the Borders through the numerous ports, commerce and migrants/visitors/travellers, as well as closer to home though journeymen, after-all tunes travelled and it is said that the Northumbrian Small Pipes were influenced by the French musette. .

There are numerous bagpipes which use the ‘closed fingering’ style as the Border pipes, some more closed than others…but this style is not wholly a Scottish fingering technique. The Asturian Gaita uses a crossed/closed fingering not unlike the Border pipes. Both are conical bored chanters and a 2nd octave can be reached by the same technique of the Galician high A fingering position.

Gaita de Boto and Ney – Snakes and Reeds

As it was a holiday in Madrid we thought to go and get out into the nature for the day. Our choice of area seemed to be the wrong one as it was heavily industrial with rubbish spoiling the river bank and the river stinking from the chemicals from the nearby factories. This did not stop the wild life from inhabiting the area though, birds and rabbits ran to hide as we walked along the rivers edge. We were walking near to the airport and every 3 minutes planes came over our heads on their way to land. I was getting a little disillusioned as the track came near to the motorway and then it ended with a gate saying “private”. We sat down and ate then headed back the same way.

What interested me was the size of the reed (cane) beds that lined the river bank, and also which grew away from the river and close to the motorway; they grew very big and a few were thick enough to cut , dry and to make open-ended flutes (nai and neys) as well as cane reed flutes.

As we walked along the path we saw a movement a few steps in front of us, a snake slithered down a hole, it was quite large, fat and light green. I am interested in the Gaita de Boto, the gaita from the region of Aragon that sometimes has a snake skin covering the chanter and drone. Green snake skin suddenly came to my mind and how it would fit nicely over my chanter!

I have reeds cut and drying in our flat for about 1 year, they need sized and experimented with to see if they are good enough to make reeds for bagpipes and to make open-ended flutes possibly of an Arabic style (nai) and perhaps a Turkish ney. The reeds near to the motorway were much better than the river bank examples, being away from the river meant they were a lot stronger, I would return and cut them later on and have a supply for a year.

I had collected a few pieces of cane to take home and as we walked I thought what an excellent place to come for  a day out, I can get my musical needs satisfied in one afternoon: snake skin for my chanter and drone, open-ended flutes from the motorway, and drone and chanter reeds from the river bank!
I did not even notice the air planes any more.

Gaita in Sanse (Madrid)

Last night, coming back from the city of mega-stores that are just outside the city of Madrid, we were sitting on the bus heading back to Alcobendas, when my friend suddenly pulling me off the seat and pushing me towards the door. I was a little surprised but I went with the flow. Once on the streets in an area commonly called ‘Sanse’  she led me back up the street and I thought maybe she wanted to return to the mega-store complex that we had just come, but there was method in her madness and very good reason it was too, as on the street corner there stood a busker playing Galician pipes. She had spotted the player while passing and was so excited that she could not tell me in so many words.

He played a gaita with 1 drone over his shoulder and by the look of his ‘open-fingering´technique a Galician chanter. We spoke with him and it was a Galican bagpipe. The single drone variety is an older type, very similar to the Asturian gaita, Gaita de Fole (Portuguese),and gaita Sanabresa, but what makes it different is the finger style as the Asturian gaita use a ‘closed fingering’ not so dis-similar to the Scottish bagpipes. The bottom hand has certain notes closed, whereas the Galican (and others mentioned) use open-fingering and plays like a Pennie-whistle.

He was from a village just outside of Madrid and he came to do some shopping and afterwards was busking. It seemed an odd place to busk on the corner of a noisy street with buses and cars passing but the volume of the gaita cut over all of the traffic noise. He found out that I was from Northern England and then played “Danny Boy” and Irish song/melody then “Amazing Grace” and Scottish melody/song. He played a Galician melody which he said was also internationally well know which it was but I am not sure its title. The internationalism of the music and instrument is becoming more common, people are getting to know each others music and instruments thanks to these international folk festivals, radio, travel, and people taking the time to play on the streets and share music with everyone who passes, and yes, he made some money too.

On Stage in Zamora (Spain)

It has been a number of years since I stood on stage alone playing solo. I remembered when I last did it back in the 90s on stage in Vilnius, Lithuania. I have played countless time since then but to stand on stage in front of about 400 people is still a nerve racking event. Playing with others is easier, you follow each other, timing is easier and just to be with another is more relaxing. I have played Border Pipes for years but hardly performed with them on stage and I choose to start the concert with them. My nerves showed for the first set of tunes, but after a while I got used to it and relaxed. When I played the Northumbrian Small Pipes I was back on familiar territory and played my set with out too much trouble.
I do not think it is the ‘standing on stage’ that is the problem with nerves it is the microphones, it can be in a room with friends or solo recording a CD, but whenever I stand in front of a microphone I grow tense, I do not play as I normal; I can not move or walk around. The microphone rivets me to a spot…curse it.

The melodies I played for the Border pipes (BP) were:
Frisky, 
Chevy Chase, 
I’m O’er Young to Marry Yet, 
Bonny Lad.

Except for Chevy Chase, which is a Border Ballad, the rest of the tunes can be found in the Peacock manuscript from the early 1800s.

The next tune I played was Bonny Pit Laddie, also from Peacock, and I played as many variations as I could remember (I think I missed one out). The style of the Northumbrian and (Scottish) Border repertoire is full of melodies with variations and to memorize them is quite a task; I fail each time but I must say I am also getting better at it too, as my playing time increases so is my memory for these variations.

Next, there was a quick change over of instruments from BP to Northumbrian Small Pipes (NSP). These are quicker to tune than the BP and less problematic to hold and to play. The melodies I played were:
Mallorca, 
Wards Brae, 
Gallowgate Lass.

The last two melodies I grouped together into one melody as they are very similar to each other.

The final group of tunes were:
Johnny Armstrong
Welcome to the Town Again,

the first being a Border Ballad melody and the last a dance tune from Peacocks.

The experience was an interesting one, enjoyable and I hope the start of many more to come in the future.
The video is of the first performance on NSP.

Sac de Gemcs and Galician Bagpipes

I am playing and practicing more Spanish melodies than I am Northumbrian melodies at the moment. Being in the UK allows me to play as much as I want with out bothering anyone. I am getting used to the Sac de Gemecs (bagpipe from Catalonia) as I had problems with its tuning. Again the original reed was not making the chanter in tune with the drones. My recent visit to Madrid produced a Galician reed in C, and when I returned to the UK I fitted it to the Sac de Gemecs and it is sounding nice and in tune with itself. I can also put more pressure on the bag to keep the drone pressure right. In short, it is a easier and nice bagpipe to play now.

I am also playing my Galician D chanter a lot in my ‘hybrid’ bagpipe. It is sounding sweet, a high pitched sound and beautifully in tune with the drones. I am practicing Catalonian and Galician melodies on this and as the fingering is nearly identical I can transfer them onto the Sac de Gemecs.

I finished a composition of a Catalonian melody played on the Sac de Gemecs called “L’arrastrat”. I used the English Concertina as a 1st and 2nd voice along side the Sac de Gemecs melody. I did the recording in the UK and later added the Concertina track in Spain. Have a listen …

My Hybrid Bagpipes

If Organology is a study of musical instruments then musical archaeology is a piecing together of facts about a time and place of that instrument.

My newly made bagpipe would tell of many layers of musical history, and as it stands today, a history that travels continents.

If we start with the oldest first:

The Drones, then we will find out that they came from India, the Punjab. I bought a set of Highland pipes in a small town in 1995. They cost me 18 UK pounds, with it I got several drone reeds and chanter reeds, in fact I bought what there was in his shop. I suspected the chanter would not be in tune but the rest of the pipe I could use for other things. In fact teh reeds fit well in my Border pipe too.
The 3 drones were in a rubber bag, very small, easily inflated but leaked a lot.
The blow pipe had a metal mouth piece which fell off after several years.
With all its faults it did play, and I did use this set of pipes for experiments over the years.
The pipe is made from wood, the chanter is conically bored and not dissimilar to the bore of my Border pipe.
I used the Indian Bass drone in my Hybrid Bagpipe, it plays in ‘Bb’ as well as in ‘A’ and by changing the drones around (removing the middle section) I can also play in ‘D’ with the same reed.
I use the cane reeds I bought in India and they are very good and reliable after so many years.
I use all stocks from the Indian bagpipe too, as well as mouth piece. I have made a few mouth piece tips to replace the metal one I lost. The ‘crack value’ i have replaced recently to make it more air tight.

The Bag I bought in Spain in 2011 from a shop in Madrid, it is a synthetic bag which is in a ‘pear drop’ design, not my favourite to hold, I think in the future I would buy/make a bag in the Highland style.
The cover was made by myself and Leila with fabric bought in Madrid and Zamora.

The Chanter/s I play are a mixture of traditions. Originally I got it to play with my Sanabresa Chanter in Bb, I turned a stock for it and connected it to the bag.
I also made a stock for my Border pipes chanter and if I tuned the drones down to ‘A’ I could get a good sound with the same reed
I also turned a stock for my Galician chanter in D, I removed the middle section of the Drone and it played a D drone to go with it.

The beauty of mouth blown pipes over bellows blown is the less time to ‘pick up and play’; and less time in tuning the drones, also with these pipes I have been able to add a Galician reed in all of them, where as to obtain a Border reed or Sanabresa reed is quite difficult.
Another advantage with this system is that I have 3 chanters and 1 bag, which saves space when transporting them and costs a lot less to buy.

Gaita Pedrazales Chanter Reeds – Galician!

When I got my Gaita Pedrazales chanter 2 weeks ago it came with 2 reeds. The chanter is beautiful, made from Santo Palo wood with nice grain.

Plastic Reed: 
One reed was made from plastic, very small stable and blades, but I could not get it to sound a octave, the top register was very sharp.

Cane Reed
The cane reed was very good, it played well with not to much pressure, it looked nice.

Since I had a class that evening I did not alter it to fit the chanter, I thought to leave it to my teacher to get it fitted properly.
In the class the teacher found it to be too flat. The Pedrazales chanter plays in Bb, and it was below that, not by much but enough to make the group of gaitas sound like a swarm of bees! So, there was two options, either push the reed further into the chanter by opening the wooden hole more to accommodate the reed or to cut a bit off the reed tip. Out came the knife and off came the reed tip, scraping to reduce pressure resulted in a sharpened reed, but still not in Bb, out came the knife and off came the reed, scraping and a chanter that played in Bb. “All is well that ends well” so the saying goes…not so.

When I got home I took out the reed and left it over night to dry. The next day the reed had warped a little. Central heating was the problem, but worse than this when I came to adjust the reed the binding came away too, leaving the 2 cane blades in my hands. The thread had unraveled, I do not know if this was due to the central heating system, but the thread and metal are not effected by heat generally? I will never know. The 2 reeds came from the same maker, but they seemed well constructed when I got them. I wrapped thread around the blades to try and make it play again, it did but not good enough for the Pedrazales.

So, 2 days after I got the chanter and reeds I had no reeds left to play the chanter! What a beginning.

The only thing to do was to use Scottish Highland chanter reeds. These HBG reeds are from Pakistan, some would say useless, but they are not so bad if one is not into competitions. They play and are cheap enough to play around with in Border pipe chanters etc. They play in A/La, and luckily my chanter was Bb. So out came the knife and off went the reed tip, until I had a chanter in Bb in the bottom note, but the top was sharp, out came the tape and the top notes played in tune. The pressure was wrong, too much and the drone stopped and I could not get the notes, too little and the bottom notes were “double toning” when all fingers were closed. I added thin wire so I could adjust the reed and keep it in position.

I took a trip to Madrid to see if they had reeds that would fit. They had some Pedrazales reeds, made by a maker in Madrid, the bindings on these reeds were glued, so they would not unravel and they looked good. I tried 3 of them but all 3 were sharp in the top notes, nothing worked. Then I tried the Galician gaita reeds for a Bb chanter. I put it in and blew…Bb exactly. The reed worked first time and it was made so I could move the reed in and out so making it Bb sharp…or flat. The pressure was nice, and There was no “double toning” in the bass notes. I was a happy man again.

Why do Bb Galician chanter reeds work in a Pedrazales chanter? Why does a Pedrazales reeds not work in a Pedrazales chanter? what is going on?

Snakes and Reeds

As it was a holiday in Madrid we thought to go and get out into the nature for the day. Our choice of area seemed to be the wrong one as it was heavily industrial with rubbish spoiling the river bank and the river stinking from the chemicals from the nearby factories. This did not stop the wild life from inhabiting the area though, birds and rabbits ran to hide as we walked along the rivers edge. We were walking near to the airport and every 3 minutes planes came over our heads on their way to land. I was getting a little disillusioned as the track came near to the motorway and then it ended with a gate saying “private”. We sat down and ate then headed back the same way.

What interested me was the size of the reed (cane) beds that lined the river bank, and also which grew away from the river and close to the motorway; they grew very big and a few were thick enough to cut , dry and to make open-ended flutes (nai and neys) as well as cane reed flutes.

As we walked along the path we saw a movement a few steps in front of us, a snake slithered down a hole, it was quite large, fat and light green. I am interested in the Gaita de Boto, the gaita from the region of Aragon that sometimes has a snake skin covering the chanter and drone. Green snake skin suddenly came to my mind and how it would fit nicely over my chanter!

I have reeds cut and drying in our flat for about 1 year, they need sized and experimented with to see if they are good enough to make reeds for bagpipes and to make open-ended flutes possibly of an Arabic style (nai) and perhaps a Turkish ney. The reeds near to the motorway were much better than the river bank examples, being away from the river meant they were a lot stronger, I would return and cut them later on and have a supply for a year.

I had collected a few pieces of cane to take home and as we walked I thought what an excellent place to come for  a day out, I can get my musical needs satisfied in one afternoon: snake skin for my chanter and drone, open-ended flutes from the motorway, and drone and chanter reeds from the river bank!
I did not even notice the airplanes any more.

Busker in Sanse

Last night, coming back from the city of mega-stores that are just outside the city of Madrid, we were sitting on the bus heading back to Alcobendas, when my friend suddenly pulling me off the seat and pushing me towards the door. I was a little surprised but I went with the flow. Once on the streets in an area commonly called ‘Sanse’  she led me back up the street and I thought maybe she wanted to return to the mega-store complex that we had just come, but there was method in her madness and very good reason it was too, as on the street corner there stood a busker playing Galician pipes. She had spotted the player while passing and was so excited that she could not tell me in so many words.

He played a gaita with 1 drone over his shoulder and by the look of his ‘open-fingering´technique a Galician chanter. We spoke with him and it was a Galican bagpipe. The single drone variety is an older type, very similar to the Asturian gaita, Gaita de Fole (Portuguese),and gaita Sanabresa, but what makes it different is the finger style as the Asturian gaita use a ‘closed fingering’ not so dis-similar to the Scottish bagpipes. The bottom hand has certain notes closed, whereas the Galican (and others mentioned) use open-fingering and plays like a Pennie-whistle.

He was from a village just outside of Madrid and he came to do some shopping and afterwards was busking. It seemed an odd place to busk on the corner of a noisy street with buses and cars passing but the volume of the gaita cut over all of the traffic noise. He found out that I was from Northern England and then played “Danny Boy” and Irish song/melody then “Amazing Grace” and Scottish melody/song. He played a Galician melody which he said was also internationally well know which it was but I am not sure its title. The internationalism of the music and instrument is becoming more common, people are getting to know each others music and instruments thanks to these international folk festivals, radio, travel, and people taking the time to play on the streets and share music with everyone who passes, and yes, he made some money too.

On Stage in Zamora (Spain)

It has been a number of years since I stood on stage alone playing solo. I remembered when I last did it back in the 90s on stage in Vilnius, Lithuania. I have played countless time since then but to stand on stage in front of about 400 people is still a nerve racking event. Playing with others is easier, you follow each other, timing is easier and just to be with another is more relaxing. I have played Border Pipes for years but hardly performed with them on stage and I choose to start the concert with them. My nerves showed for the first set of tunes, but after a while I got used to it and relaxed. When I played the Northumbrian Small Pipes I was back on familiar territory and played my set with out too much trouble.

I do not think it is the ‘standing on stage’ that is the problem with nerves it is the microphones, it can be in a room with friends or solo recording a CD, but whenever I stand in front of a microphone I grow tense, I do not play as I normal; I can not move or walk around. The microphone rivets me to a spot…curse it.


The melodies I played for the Border pipes (BP) were:
Frisky, Chevy Chase, I’m O’er Young to Marry Yet, Bonny Lad.
Except for Chevy Chase, which is a Border Ballad, the rest of the tunes can be found in the Peacock manuscript from the early 1800s.
The next tune I played was Bonny Pit Laddie, also from Peacock, and I played as many variations as I could remember (I think I missed one out). The style of the Northumbrian and (Scottish) Border repertoire is full of melodies with variations and to memorize them is quite a task; I fail each time but I must say I am also getting better at it too, as my playing time increases so is my memory for these variations.

Next, there was a quick change over of instruments from BP to Northumbrian Small Pipes (NSP). These are quicker to tune than the BP and less problematic to hold and to play. The melodies I played were:
Mallorca, Wards Brae, Gallowgate Lass.
The last two melodies I grouped together into one melody as they are very similar to each other.
The final group of tunes were:
Johnny Armstrong and Welcome to the Town Again,
the first being a Border Ballad melody and the last a dance tune from Peacocks.

The experience was an interesting one, enjoyable and I hope the start of many more to come in the future.

The video is of the first performance on NSP.